Extrusion International 1-2017

34 Extrusion International 1/2017 PERIPHERAL EQUIPMENT A new-generation coextrusion feedblock from Nordson Corporation enables processors of film, sheet, and coatings to fine-tune individual layers as well as accommodate changes in layer ratio, and to adjust the tuning systemwithout removing the feedblock from the production line. G. Iuliano, business development manager for polymer dies. “This provides more area for tuning layer thickness uniformity and thus makes possible more accurate and effective tuning. In addition, changing the position of the profile bars dramatically changes the result, allowing for significant process refinements to be made on- the-fly.” The positioning of the profile bars with respect to the combining point is adjusted by rotating the profiling actuators. This is accom- plished by turning nuts on the outside of the feedblock in accor- dance with a position indicator and does not entail stopping pro- duction. The profile bars are available with various surface configurations, including a standard bar with a uniform raised surface and others designed to correct such issues as heavy end flow, heavy center flow, or “M” or “W” patterns. The bars are installed in dovetail grooves in the surface of the profiling actuators. A cover plate in the feedblock provides access for replacing one set of bars with another. Adjusting the profiling actuators in the Ultraflow V-T feedblock makes it possible to influence the distribution of a par- ticular layer. If further adjustment is necessary, one can replace the profile bars by briefly stopping production, without having to re- move the feedblock from the extrusion line. Nordson will specify a feedblock whose flow channel differs in size from the standard 4 in. (100 mm), with widths available from 2 in. (50 mm) up to 7 in. (180 mm) depending on the width of the product to be extruded. Larger volume feedblock channels reduce the shear stress levels at the layer interfaces and a wider feedblock channel contributes to a more consistently on-specification product. In the case of a 100-in. (2,540-mm) die, for example, the spreading ratio is 25:1 for a 4-in. feedblock channel but only about 14:1 for a 7-in. channel. As in the Ultraflow V feedblock, the combining planes in the new Ultraflow V-T system combine polymers in a parallel-path manner, achieving optimal layer ratio stability throughout the structure. Their ability to be adjusted ‘on the fly’ increases uptime and allows for greater end-product versatility. The Ultraflow V-T feedblock is available with Nordson’s optional selector spool that allows the layer sequence to be pre-arranged upstream of the combining point, without removing the feedblock from the production line. A feedblock combines melt streams from separate extruders into a multi-layer “sandwich” that the extrusion die subsequently dis- tributes to target product width. The new EDI™ Ultraflow™ V-T feedblock has separate devices for fine-tuning layer stability and thickness uniformity, and both are capable of being adjusted with- out stopping production. As in the widely used Ultraflow™V feed- block, one of these devices is a pair of “combining planes” (located where the outer-layer melt streams join the core layer in the cen- tral flow channel) that fine-tune the overall structure by adjusting the gaps at the point of layer combination. What is new is a pair of “profiling actuators” (located opposite the combining planes) within which are mounted interchangeable “profile bars” that fine-tune the thickness uniformity of the individual layers (see sche- matic). For coextrusion of more than three layers, additional tuning devices are placed farther downstream, where more melt streams join the central structure. “Because the profiling actuators are large in diameter, they ac- commodate wider profile bars and enable them to be positioned either close to or farther from the layer combining point,” said Sam www.nordson.com Internal Components of Feedblock Schematic of internal working components of EDI™Ultraflow™V-T feedblock shows fine-tuning of a three-layer coextrusion. Flow direction is from left to right. First, two tear-drop shaped “combining planes” tune the overall structure by adjusting the gaps at the point of layer combination, where the outer-layer melt streams (blue and gold) join the core layer (red) in the central flow channel. At the same time, two cylinder-shaped “profiling actuators” (located opposite the combining planes) tune the thickness uniformity of the individual layers by means of interchangeable “profile bars” (brown components mounted on the profiling actuators. For coextrusion of more than three layers, additional tuning devices are placed farther downstream, where more melt streams join the central structure New feedblock fine-tunes each layer